ARRIS C250 V2 FPV combo with Teleportor V5 goggle is good for both beginners and experts. Compared with ARRIS X-Speed 250B V3, the ARRIS C250 V2 is much lighter due to the pure carbon fiber frame and simple structure.With the ligher weight and powerful motor, the C250 is faster and agile.
1. Simple structure frame installed with tower structure ESC/PDB, easy to assemble and easy to repair.
2. High quality 3K Carbon fiber frame, the material is imported from Janpan
3. 4mm thick arms, super strong and durable
4. Super Light frame, only $136g
5. The tower ESC/FC comes with integrated OSD, no need to install it separately
6. The angle of the FPV camera is adjustable
7. 4mm thick arms, super strong and durable
8. High efficiency X2205 2300KV motor provides you better performance and longer working life
9. High quality 5042 3 blade propeller, 10% higher effeciency than normal propellers
10. High safety 4S 1500mah 50C lipo battery
Dimension:195mm x 230mm x 42mm (Propellers not included)
Diagonal Wheelbase: 250mm
Flight Controller: F3 flight Controller
Frame Material: Pure Carbon fiber sheet
Radio System: Radolink AT9 with R9DS receiver
Camera: 1000TVL HD video canera
FPV TX: 5.8G 200mw 40CH
Antenna: 5.8G Antenna
Flying Time: 10min hovering
Battery: ARRIS 4S 1500mah 50C Lipo
Goggle: Fatshark Teleportor V5 FPV Goggle
ARRIS C250 V2 is made of pure carbon fiber material. The upper plate and side plate adopts 1.5mm pure carbon fiber material, decrease the weight of the whole frame. Meanwhile, the motor arm adopts 4mm carbon fiber material, ensure the strength of the frame. The total weight of the frame is about 137g.With the simplify one-piece design and lower gravity center design, all kinds of flight actions can be done with facility.
The layout design of the C250 V2 is reasonable, the standard flight controller and PDB board can install there.On the frame, there is reserved space for the XT60 female battery connector.The motor arm has holes for 220x series motors, and both 5 inches and 6 inches propellers can install on the C250 V2 frame.
The main advantages of the 4in1 30A Tower:
1. With the double layer design, you just need to plug the pins between esc and flight controller, flight controller and other electronic components. The layout is more concise, decrease the weight of the drone, provided guarantee for flight performance improvements.
The power for flight controller and camera is provided by the BEC on the flight controller. The power for video transmitter is provided by battery. This improves the anti-interference of the video transmission.
2. The tower integrated the OSD, avoid to install it additionally and the adjustment.The drone could get a quick response to the throttle during the flight.
3. The Tower structure design protects the ESC well during the flight. According to our experience, some of the ESC were damaged by the propeller rotation or tree brunch cut, and some of the ESC were damaged due to the broken of the motor arm during the crash when it installed on top of the motor arm. Sometimes, in order to protect the ESC, we added ESC cover to protect it. From this, the weight of the drone increased. For this tower, the esc integrated in the tower which installed in the middle of the quad frame, the ESCs can be protected quite well and make it looks better.
With the high performance ARRIS X2205 2300KV brushless motor
, the ARIS C250 has outstanding power. ARRIS X2205 motor is one specially designed high end motor for professional fpv racing drones from ARRIS. From the choices of the magnet steel, wires, bearing and other materials to CNC processing and final test, ARRIS tried to take the best from the best in each step. In the end, the ARRIS X2205 motor has be great performance on power output, resist high temperature and working in sustaining large current condition.
The ARRIS C250 V2 adopts with the latest 5042 propeller, it has bigger windward area, well balance and strengthen root, and the efficiency is 10% higher than normal propeller. This propeller is the first choice of FPV racing drones.
ARRIS 5.8g 200mW 40-CH video TX pre-assembled. The ARRIS TS5823S transmitter packs 200mW of ultra clean 5.8GHz power in a micro sized video/audio transmitter! A must for those looking save size and weight while still getting good performance. The ARRIS TS5823S is transmitting a full range of 40 channels and only weighs 10g. It's perfect for a wide range of aircraft!With a goggle or monitor in hand, you can begin your FPV journey.
ARRIS C250 V2 has integrated with a remote controller battery warning buzzer, pilot can set the threshold (adjustable)according to CF parameter-adjustment software. In addition, you can also locate your racing drone through triggering the buzzer with the switch D on the transmitter.
Self-level mode is the easiest to fly, because when you leave the stick at the centre and not controlling it, your drone just level itself and stays there. But Most advanced pilots would tell you they fly in Acro mode ALL THE TIME. Here are some of the advantages of Acro mode.
Manual mode is useful for acrobatics such as flips or rolls, or FPV when smooth and fast control is desired. The picture below is what we set on our own Radiolink AT9 Radio.
RadioLink AT9 9-Channel 9CH 2.4GHz Transmitter + R9D Receiver.The AT9 radio is with high performance-price ratio. And it can support strength, receiver voltage monitored, extending battery voltage, temperature, motor RPM, GPS etc.
High safety ARRIS 4S 1500mah Lipo Battery
ARRIS 4S 1500mAh 50C lipo battery is specially designed for FPV racer. The price of this battery is much higher than the similar batteries in the market, because we only sell top-quality batteries. As we all know, the low quality battery might have potential safety hazard, we will never tolerate such products.For ARRIS 4S 1500mah lipo battery, we have done UN38.3 test,1.2M Drop test,MDS report for it, for the test report, you can check here.
Hobby-Wing.com is the power seller of Fatshark. 100% genuine, please feel free to buy.
Make your first FPV experience simple and fun. The Teleporter V5 is a full function, self-contained FPV goggle that includes FPV features normally only found on higher end models. To start enjoying FPV, simply power the goggles with the included battery pack and connect the transmitter/camera to the balance lead of your onboard RC LiPo battery pack. The Teleporter V5 features digital head tracking technology that eliminates the need for special RC radios as the display can zoom in on the image while the head tracker controls the viewing window (works best with a wide angle lens on a fixed camera). The head tracker also supports traditional pan/tilt servo mounted camera with trainer-equipped radios.
Large virtual image (25¡éX FOV, diagonal)
Crisp QVGA resolution display (320 X 240)
NTSC/PAL Auto Selecting
Precision 9DOF 2-axis Head Tracker
Integrated 5G8, 7CH NexWave RF Receiver
Head tracker works in conventional mode (trainer radio) and digital zoom mode (no special RC radio required)
Requires (Not include):
RC charger (to charge headset battery)
1 x ARRIS C250 V2 Racing Quad Frame
4 x ARRIS X2205 2300KV Brushless Motors
1 x Flycolor Tower w/ F390 30A 4 in 1 ESC + F3 + OSD + PDB
4 x ARRIS 5042 3-blade Propeller
1 x 1000TVL 2.8mm camera
1 x 5.8G 200mw 32CH FPV TX
1 x FPV Transmitter Antenna
1 x Radiolink AT9 Transmitter with receiver
1 x ARRIS Buzzer
1 x ARRIS 4S 1500mah Lipo Battery
1 x Fatshark Teleporter V5 Goggle
Battery Charger is sold separately.